Return
Home
Links
FAQs
Contact
Us
main
T3
 
 

GREAT NEWS FOR PROBLEM WELLS/BORES, in fact all wells/bores

A SIMPLE solution to your submersible pump problems:

7 critical reasons why the Patented Feri submersible well/bore pump outshines the others


  • Because it was designed specifically to operate in some of the most adverse conditions in outback Australia.


  • Because it cannot seize due to the bore/well being low on water or the water contains a lot of suspended solids such as sand or grit


  • Because it cannot corrode, as it is constructed entirely of tough plastics


  • Because you can easily install it yourself and move it from one location to another


  • Because it can be a long way from a power source


  • Because there are no lengths of piping and rods to disassemble, no power cords to mess with, no bits and pieces to drop down the hole.


  • Because as it is a light pump (less than 5 kg - 10 lb) hanging on the end of poly piping, it can be easily removed from a well/bore and re-located to another one in a different location.





    • - Are you tired     of paying big bucks to replace or overhaul your submersible because it
    runs dry and wears out in a short time?

     - Don’t want to spend thousands of Dollars to run power cables to the site of your new well/bore

     - Had enough     of dis-assembling head works, rods and electrics to pull a broken down
    pump out of your well/bore

     - The water in your well     is corroding, eroding away or blocking up conventional pumps

    If the answer to any of these questions is a resounding YES, then the Feri low pressure air operated submersible pump is the answer.


    To quote Dr K Y Cheng from the University of Western Australia:

    "The simplicity of operation, the relative easy access of power source and the robustness of the pump make it a worthwhile consideration in a range of applications."

    If the water depth in your well/bore is MORE than 35% of the total vertical lift height, the Feri T1 pump will work great for you. (if your water depth is less than 35% please click HERE) All you need is a small compressor, which can be located literally a couple of miles or more from the well/bore site and run a cheap air line to the pump. Alternatively you can have a compressor running on diesel, petrol (gasoline), coupled to a windmill or powered by solar panels.

    The choice is yours.

    Easy to Install

    Just simply connect the water delivery line (usually 1 1/2 or 2 inch) and the air line to the pump, usually poly piping, which is available in great lengths. Lower it down the hole, connect the other end of the air line to the compressor (usually 2 - 30 cfm, 5 - 12 cfm is most common and you may already have one) and turn on the air. Wait a few seconds and you get water.

    The principle of the Feri pump is very simple. It uses the natural lifting force of air to do the work.

    Pressure required is around 1psi (6.9kpa) per Meter or 3ft of lift.

    Submersion in water should be no more than 70 meters (210ft), as this falls within the maximum working pressure of most regular compressors.



    The amazing Feri submersible well/bore pump comes with a 5 year warranty against faulty workmanship and a 30 day money back
    guarantee     (note 1).

    NOTE:  As the Feri utilizes the natural forces of nature, for best performance and because it discharges a mixture water and air, it needs to have minimal restrictions in the delivery line and pump to an open receiver such as a tank.

    The deeper the submersion, the more water is produced, but more pressure is required

    The following charts are an example of the Feri pump's performance through 1 1/2 inch (40mm) delivery line. The possible operating range is much larger - top and bottom of the range. Our deepest installation to date is 660ft (220m)
    Click to download U.S. Charts
    Click to download Metric charts
    Standard Feri pump models are designed to fit into 4" (100mm) or larger casings.


    What are the alternatives?

    • Digging an expensive trench to house expensive power cables to the well/bore site for an electric pump?
    • Getting permits and paying electricians to install an electric?
    • Having to use derricks, winches and man power to install and remove a conventional pump?
    • Replacing your electric or jet pump because the well has run out of water and destroyed the pump?
    • Replacing your conventional pump because sand and solids in the water have quickly destroyed it
    • Replacing your conventional pump because the ph in the water is a little off and has corroded and destroyed metallic parts of the pump?

      None of the above problems apply to the Feri, which is cheap, simple and quick for one person to install
      (unless the well is exceptionally deep)

      You can put up with all the above mentioned problems and expenses OR you can put in your order now and save time, money and frustrations and quickly get pumping beautiful water from your well, bore or other source. We have 25 T1 pumps at the reduced price of $725AU (around $545US). Once they are gone, the price goes up

    For U.S. and Australian customers: To order your pump online right now, click

    If you are elsewhere in the world or have any questions, please email us at info@theferipump.com or Phone 618 9574 4525

    Delivery time to USA mainland and Australia is around 7 - 10 days.

    If a standard Feri pump model does not suit your requirements, please contact us and we may be able to build one that does.

    Note 1: If returning the Feri pump for a refund, it must be in undamaged and as new condition. Freight is the responsibility of the purchaser.




    | Charts |
    | Return Home | Links | FAQs | Contact Us | main | T3 |
    		 
     



    Copyright © 2008, feripump.com. All rights reserved.